- bldctool Capture.JPG (38.43 KiB) Viewed 11521 times
I'll try 2.16 this week.
Nunchuck Schematic NRF SPI
-
Blasto
- Posts: 21
- Joined: 19 Dec 2015, 03:45 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
ah... haven't tried 2.16 yet. i'm still on 2.13 and I don't have a NRF tab.
I'll try 2.16 this week.
I'll try 2.16 this week.
-
Dude
- Posts: 33
- Joined: 30 Dec 2015, 23:37 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
Hi Blasto, I tried with 2.16 and set the controller id to 15 ... unfortunately it did not connect. I'll wait, if you will make it run in 2.16 - if not I have to try 2.13 too.
Edit: ok, also failed with FW2.13
Edit: ok, also failed with FW2.13
-
Dude
- Posts: 33
- Joined: 30 Dec 2015, 23:37 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
Ok - Let me try it the other way round, maybe I get an answer on that:
Who has a running NunchukNRF, with which Board (4.7, 4.11, ...) and with which Firmware (FW2.13, 2.16, ...)?
Dude
Who has a running NunchukNRF, with which Board (4.7, 4.11, ...) and with which Firmware (FW2.13, 2.16, ...)?
Dude
-
Blasto
- Posts: 21
- Joined: 19 Dec 2015, 03:45 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
- Attachments
-
- Capture.JPG (34.04 KiB) Viewed 11353 times
-
hexakopter
- Posts: 86
- Joined: 24 Dec 2015, 15:24
- Location: Germany [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
When just using R10 for the address resistor that means a 8 for the ID right? I found nowhere if the 1 begins using R7 and then count to the right or with R10 and the count to the left.
But also when just R10 means a 1 I don't get my Nunchuk working under FW2.16. Don't tested FW2.13, but I thought the only thing I must change is the last number of the Adress in the NRF Tab to this resistor address value and change the App to NRF.
But when doing that the red LED just blinks ones when pressing C and Z. The same like it is doing when I don't have a receiver module plugged to the VESC. Is there a possibility to restrict the fault source? Maybe my cheap NRF24l01 modules are not working correctly or something else. I don't know.
Have connected CE to VCC and use a 10u Cap and did everything like in this thread, but no success.
Maybe someone of you have an idea.
But also when just R10 means a 1 I don't get my Nunchuk working under FW2.16. Don't tested FW2.13, but I thought the only thing I must change is the last number of the Adress in the NRF Tab to this resistor address value and change the App to NRF.
But when doing that the red LED just blinks ones when pressing C and Z. The same like it is doing when I don't have a receiver module plugged to the VESC. Is there a possibility to restrict the fault source? Maybe my cheap NRF24l01 modules are not working correctly or something else. I don't know.
Have connected CE to VCC and use a 10u Cap and did everything like in this thread, but no success.
Maybe someone of you have an idea.
-
chipoi84
- Posts: 2
- Joined: 25 Apr 2016, 16:51 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
Did you open the 'nunchuk" tab and enable "Current"? You can also test if it is receiving any signal by leaving it "disable" and click on "display" box.
-
hexakopter
- Posts: 86
- Joined: 24 Dec 2015, 15:24
- Location: Germany [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
Yes, I tested that. But when I understand it right, if the connection is working the red LED should stay on. So I checked if it stays on, but it didn't.
-
chipoi84
- Posts: 2
- Joined: 25 Apr 2016, 16:51 [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
Have you try to populate all of the resistor and use 15 in the address box?
-
hexakopter
- Posts: 86
- Joined: 24 Dec 2015, 15:24
- Location: Germany [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1236: count(): Parameter must be an array or an object that implements Countable
Re: Nunchuck Schematic NRF SPI
No, just R10 is soldered. I can solder the others later, but that makes no sense when everybody is using all. (so everybody with address 15)
That makes the "different ID" feature useless.
That makes the "different ID" feature useless.
Who is online
Users browsing this forum: No registered users and 1 guest